All base, body and air horns are stamped prior to disassembly to ensure units are reassembled with the
proper “companion” parts. Internal parts such as jets and metering rods are identified, to ensure they
remain with the original castings, where variations may have occurred at the manufacturing level. This process ensures
that original flow characteristics are maintained.
After disassembly all parts are inspected and cleaned in
industrial equipment. Internal parts such as gaskets, needle and seats and plunger cups are discarded. All white metal
castings are chemically processed to restore the factory finish. All aluminium castings are sandblasted or tumbler
processed to restore the finish. Bases are surfaced to ensure proper mating with the body assembly and the manifold.
Mounting holes are refaced to assure proper torque of mounting fasteners.
During the sub-assembly process
all threads, inlets and vacuum pipes are inspected and repaired or replaced if necessary. Throttle and choke plates
are inspected and replaced if not serviceable. Throttle bushings are installed wherever throttle shaft play is not within
tolerances. Completed base assemblies are checked for vacuum integrity. Any base that does not meet specifications
must be repaired prior to use.
Throughout the assembly process all body and calibration components are reassembled
to the original unit to maintain product calibration. All assembly components are tested prior to product assembly.
Completed product is flow tested throughout all ranges of operation to ensure proper calibration. Choke adjustment,
idle speed and air-screw settings are made during product testing. This process allows the technician to start the vehicle
upon product installation. Final adjustments may be necessary due to varied engine condition.
All Autoline
Carburetors are heat shrink packaged with installation instructions, mounting gaskets and specific technical bulletins.
Important Install Notices:
Mounting Plate (Chrysler 1.7,2.2 litre applications): Prior to installation of this carburetor, the mounting plate between the carburetor and the manifold should be thoroughly
inspected, and if necessary replaced. This is a dealer part. It is common for this part to deteriorate from the intense heat
in this area. Installing a carburetor on a substandard mounting plate will result in vacuum leaks and unsatisfactory idle conditions.
Secondary Choke Plate: This model of carburetor varied in the design of the choke system. In appearance, units are manufactured
with either a one choke plate or a two choke plate system. The carburetor may appear to be different from the original unit, however its
operation and performance on the vehicle not be affected.
Verhindern Sie Vergaserüberflutung / vorzeitiges Ausfallen!
Vermeiden Sie Kraftstoffmischungen mit hohem Ethanolanteil. Informationen zu den Kraftstoffanforderungen finden Sie im Benutzerhandbuch.
Ethanol kann Ablagerungen aus dem Kraftstofftank, den Kraftstoffleitungen und anderen Komponenten des Kraftstoffsystems, die ursprünglich nicht für Ethanolmischungen ausgelegt waren, lösen und entfernen.
Ersetzen Sie immer den Kraftstofffilter und spülen Sie die Kraftstoffleitungen, wenn Sie den Vergaser ersetzen oder warten.
Schmutz und Ablagerungen aus ungefiltertem Kraftstoff können sich zwischen Einlassventil und Sitz festsetzen und zu Überschwemmungen führen.
Denken Sie daran, Kraftstoffstabilisator in den Kraftstofftank zu geben, wenn das Fahrzeug über einen längeren Zeitraum nicht gefahren wird.
Kraftstoffstabilisator verhindert, dass Benzin verdampft und/oder klebrige Harze bildet, die den Vergaser verstopfen können.
Wenn Sie Schwierigkeiten bei der Auswahl des richtigen Autoline-Teils haben oder Probleme während oder nach der Installation dieses Teils auftreten, stehen Ihnen die ASE-zertifizierten Techniker von Autoline zur Verfügung, um Ihre Fragen zu beantworten.
Anmerkung für Kunden in Kalifornien - Warnung: Dieses Produkt kann Sie Chemikalien aussetzen, inklusive Blei und Mineralöle die im US-Bundesstaat Kalifornien als Ursache für Krebs, Geburtsfehler oder andere Schädigungen der Fortpflanzungsfähigkeit eingestuft werden. Für mehr Informationen siehe: www.P65Warnings.ca.gov
Erstausrüstung / alternative Artikelnummern: H26520, R400651
AUTOLINE Garantie Information:Drosselklappen und Verteiler 12 Monate. Einspritzventile und Diesel Produkte 24 Monate. Vergaser 90 Tage.Details zur Garantie