|
WJB / INMOTION PARTS WLK035
|
|
$196.79
Price
|
$0.00
Core
|
+ Sold in packs of 1x1
Pack
|
$196.79
Total
|
|
|
|
|
|
| WJB / INMOTION PARTS WLK035 Specifications |
|---|
| Height (Inch) | 10.44 | | Height (MM) | 265.176 | | Length (Inch) | 16.08 | | Length (MM) | 408.432 | | Width (inch) | 16.08 | | Width (MM) | 408.432 |
|
|
| Includes Snap Ring, Bearing, Knuckle, Hub Assembly, Backing Plate, Backing Plate Mounting Bolts, Deflector & Axle Nut |
WJB Wheel Bearing, Hub and Knuckle assemblies eliminate the most challenging steps of pressing the old wheel hub out of the bearing, pressing the old bearing out of the steering knuckle and then pressing in the new parts. Each complete knuckle assembly comes pre-assembled so it is ready to install right out of the box!
Features & Benefits:
- Include all components required for installation
- Pre-assembled to eliminate risk of improper press usage and seating alignment
- Steering knuckle is coated to minimize rust
- Manufactured in ISO/TS 16949 certified factories
Additional Information About WJB's Knuckle Assemblies
 Benefits of Purchasing a Wheel Bearing / Hub / Knuckle Assembly Purchasing a Wheel Bearing & Hub kit is less expensive up-front, but a complete Wheel Bearing / Hub / Knuckle Assembly provides added benefits:
| ✓ | Reduce Install Time & Difficulty: Unlike Wheel Bearing & Hub Kits, which require the use of a hydraulic press for proper installation, a complete Wheel Bearing / Hub / Knuckle Assembly does not require a press, making installation faster, simpler and cheaper. |
| ✓ | Simplify Shopping: An assembly includes all of the necessary parts, including the seal, lock ring and axle nut, so you don't have to identify and purchase each component separately. |
| ✓ | Save Money: The cost of the assembly is often cheaper than buying the components individually, and means you only have to do the job once. |
Symptoms Of A Failing Wheel Bearing & Hub
Wheel hub units are low maintenance parts, but that doesn’t mean they last forever. Uneven road surfaces, heavy driving conditions (such as towing or racing), and under-inflated tires put extra strain on the hub bearing and can lead to premature failure. Common signs of a bad hub unit include:
- A humming, rumbling or growling noise that increases with acceleration
- A loud constant whining or grinding noise when the vehicle is in motion
- Excessive play in the steering wheel
- Steering wheel vibration that changes with the vehicle speed or as the vehicle turns
- ABS system malfunction
How To Identify The Faulty Wheel Bearing & Hub
It is often difficult to pinpoint which hub unit has gone bad while driving because noise and vibration
travels through the frame of the vehicle. Here are a two tests you can do to help identify which hub unit has gone bad:
Shake Test: Identifying Play or Looseness
- Lift your vehicle so the wheel is off the ground
- Place your hands on the sides of the tire and try to shake the wheel
- Now place your hands on the top and bottom of the tire and try to shake the wheel again
- If you feel movement in both directions, you have play in your bearing and it needs to be replaced
- Note: If you feel movement when shaking the wheel left to right, but not top to bottom, you could have a worn out tie rod end. Similarly, if you have movement top to bottom, but not left to right, you may have a worn out ball joint.
Spin Test: Identifying Noise or Grinding
- Lift your vehicle so the wheel is off the ground and can spin freely
- Spin the wheel, in either direction, and listen for a grinding or howling noise
- If you hear a loud grinding or howling noise, that increases with the speed of the wheel, you have a failed bearing that needs to be replaced
- Note: It is best to test both front or both rear bearings at the same time so you can compare the difference between the two sides. If you have a failed bearing, there will be a noticeable difference in the amount of noise you hear during this test
|
WJB / INMOTION PARTS Warranty Information:12 Months |
|
